In the previous question if the floor has micro pores and water penetrates the floor at a constant rate of 0.1kg/m2h, what will be the time required for the water layer to disappear?

In the previous question if the floor has micro pores and water penet

1.	In the previous question if the floor has micro pores and water penetrates the floor at a constant rate of 0.1kg/m2h, what will be the time required for the water layer to disappear?
A.	3.64h
B.	4.73h
C.	5.94h
D.	2.36h
Answer» B. 4.73h

Discussion

No Comment Found

Related MCQs

In the previous question if the floor has micro pores and water penetrates the floor at a constant rate of 0.1kg/m2h, what will be the time required for the water layer to disappear?
In an accident a container containing ethanol(s.g 0.789) falls down in a room of dimension 1*1*2(all in m). Ethanol forms a layer of 2mm. Ethanol vaporizes and diffuses through a stagnant film of air of thickness 2.5mm. What will be the time required for the water layer to disappear completely. The diffusivity of ethanol in air is 2.567*10-5 m2/s. the total pressure is 1.013 bar and the pressure of ethanol in bulk air is 0.02244 bar and at the ethanol-air interface is 0.02718bar. The temperature is 25.2°C.
In order to prepare Lithium nitride, air is passed gently over a reactor. Suppose that Nitrogen diffuse to a length 5cm before getting reacted with Lithium. Nitrogen reacts with lithium quickly so that partial pressure of Nitrogen at that point is 0. Reactor is a cylinder of length 10cm and diameter 2cm. Assume air to be a mixture of Nitrogen and Oxygen only. The temperature is 298K and total pressure 1atm. Diffusivity of N2 in O2 is 2*10-5m2/s. Calculate the Molar flux (mol/m2.s) of N2 at a distance of 2.5cm from the top with respect to an observer moving with twice the mass average velocity a direction towards the liquid surface. (R=8.205*10-5m3atmK-1mol-1). Assume z=0 at the top of the reactor.
Oxygen diffuses through a stagnant layer of air, 1mm thick, ambient temperature 28°C and 1atm total pressure. The partial pressure of oxygen on two sides of layer is P1=0.9atm and P2=0.1atm respectively. Calculate the value of Molar flux (in mol/m2.s) with respect to an observer moving with molar average velocity. Calculate this value at the end of the path where P2=0.1atm. Use R=8.205*10-5m3atmK-1mol-1.
For a gas mixture (A+B) equimolar counterdiffusion takes place. Which among the following statements are correct for molar flux?
A cylinder of sulfur is kept in a large volume of stagnant air for sublimation. How much time will be required for its complete sublimation?
The molar average velocity of the components in a binary mixture in which they are in equimolar counter diffusion is
In the previous question if the floor has micro pores and water penetrates the floor at a constant rate of 0.1kg/m2h, what will be the time required for the water layer to disappear?
In an accident a container containing ethanol(s.g 0.789) falls down in a room of dimension 1*1*2(all in m). Ethanol forms a layer of 2mm. Ethanol vaporizes and diffuses through a stagnant film of air of thickness 2.5mm. What will be the time required for the water layer to disappear completely. The diffusivity of ethanol in air is 2.567*10-5 m2/s. the total pressure is 1.013 bar and the pressure of ethanol in bulk air is 0.02244 bar and at the ethanol-air interface is 0.02718bar. The temperature is 25.2¬¨¬®‚Äö√†√ªC.$
A binary liquid mixture is separated by distillation process. The more volatile A vaporizes while less volatile B gets transported in opposite direction. Latent heat of vaporization of A and B is 0.5unit and 1unit respectively. What will be the relation between molar flux of A and B

In the previous question if the floor has micro pores and water penetrates the floor at a constant rate of 0.1kg/m2h, what will be the time required for the water layer to disappear?

Discussion

No Comment Found

Related MCQs

Reply to Comment