MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 1232 Mcqs, each offering curated multiple-choice questions to sharpen your Electrical Engineering knowledge and support exam preparation. Choose a topic below to get started.
| 501. |
The crack depth measurement is possible in |
| A. | magnaflux test |
| B. | eddy current test |
| C. | ultrasonic test |
| D. | both b and c |
| Answer» E. | |
| 502. |
The result can be recorded by permanently in |
| A. | magnaflux test |
| B. | eddy current test |
| C. | dye penetrant test |
| D. | radiography |
| Answer» E. | |
| 503. |
Response of eddy current is depends upon |
| A. | magnetic permeability |
| B. | electrical conductivity |
| C. | structural defects |
| D. | all of the above |
| Answer» E. | |
| 504. |
If the care is not taken during magnaflux test then. .... is possible |
| A. | local heating and sparking |
| B. | explosion |
| C. | harmful uv radiation |
| D. | none |
| Answer» B. explosion | |
| 505. |
The purpose of developer is to make the penetrant |
| A. | in the crack invisible |
| B. | in the crack visible |
| C. | chemically highly reactive |
| D. | all of the above |
| Answer» C. chemically highly reactive | |
| 506. |
The circular cracks are detected in magnaflux test by |
| A. | circular magnetizatio n |
| B. | longitudinal magnetizatio n |
| C. | demagnetiza tion |
| D. | all of the above |
| Answer» C. demagnetiza tion | |
| 507. |
The horizontal cracks sre detected in magnaflux test by |
| A. | circular magnetizatio n |
| B. | longitudinal magnetizatio n |
| C. | demagnetiza tion |
| D. | all of the above |
| Answer» B. longitudinal magnetizatio n | |
| 508. |
Which one is not a part of magnaflux process? |
| A. | surface preparation |
| B. | magnetizatio n |
| C. | demagnetiza tion |
| D. | observation under microscope |
| Answer» E. | |
| 509. |
Principle of operation of eddy current test is based on the |
| A. | development of emf |
| B. | types of current supplied to the material |
| C. | piezoelectrici ty |
| D. | ferroelectrici ty |
| Answer» B. types of current supplied to the material | |
| 510. |
Eddy current test may be used to find out |
| A. | defect |
| B. | type of the heat treatment given to material |
| C. | change in chemical composition |
| D. | all of the above |
| Answer» E. | |
| 511. |
Which one may be used as material for transducer in ultrasonic test? |
| A. | steel |
| B. | quartz |
| C. | polymer |
| D. | none |
| Answer» C. polymer | |
| 512. |
Internal defects inthe steel component cannot be detected by |
| A. | magnaflux |
| B. | radiography |
| C. | ultrasonic |
| D. | none |
| Answer» B. radiography | |
| 513. |
Level of liquid in the sealed container may be checked by |
| A. | magnaflux |
| B. | dye penetrant |
| C. | radiography |
| D. | eddy current |
| Answer» D. eddy current | |
| 514. |
Dimension and accuracy in the products may be checked by |
| A. | dye penetrant |
| B. | magnaflux |
| C. | radiography |
| D. | eddy current |
| Answer» E. | |
| 515. |
Which type of the test is mostly used for the inspection of the grinding and fatigue cracks on tool steeel? |
| A. | magnaflux |
| B. | ultrasonic |
| C. | radiography |
| D. | eddy current |
| Answer» B. ultrasonic | |
| 516. |
Oil couplant used in the ultrasonic test to |
| A. | make surface smooth |
| B. | avoid air gap |
| C. | reduce friction |
| D. | fill the surface flaws |
| Answer» C. reduce friction | |
| 517. |
........is used to inspect the inside portion of a hollow chamber,narrow tube or a bore |
| A. | boroscope |
| B. | optical microscope |
| C. | endosope |
| D. | telescope |
| Answer» B. optical microscope | |
| 518. |
...........is commonly used for visual inspection method |
| A. | boroscope |
| B. | optical microscope |
| C. | endoscope |
| D. | telescope |
| Answer» C. endoscope | |
| 519. |
The defects like mould shifts,surface roughness,blow holes etc can be easily detected by ......... method. |
| A. | radiography |
| B. | visual inspection |
| C. | eddy current |
| D. | ultrasonic |
| Answer» C. eddy current | |
| 520. |
...........test does not damage the workpiece while testing |
| A. | magnaflu |
| B. | hardness |
| C. | bend |
| D. | torsion |
| Answer» B. hardness | |
| 521. |
...........does not damage the workpiece. |
| A. | creep and fatigue |
| B. | brinell and rockwell |
| C. | tensile and erichson test |
| D. | none |
| Answer» E. | |
| 522. |
In magnaglo, the wavelength of ultraviolet light is |
| A. | 2500 to 3000a ° |
| B. | 3500 to 4000a ° |
| C. | 4500 to 5000a ° |
| D. | none of the above |
| Answer» C. 4500 to 5000a ° | |
| 523. |
Detection of subsurfae depends on                    , in MPT |
| A. | the strength of magnetic field |
| B. | the strength of ac magnetic field |
| C. | both a & b |
| D. | none of the above |
| Answer» B. the strength of ac magnetic field | |
| 524. |
In MPT, detection of subsurfae depends on |
| A. | the strength of ac magnetic field |
| B. | width of discontinuity |
| C. | the strength of ac voltage |
| D. | none of the above |
| Answer» C. the strength of ac voltage | |
| 525. |
                     current magnetization makes it possible to detect surface as well as subsurface discontinuities. |
| A. | ac |
| B. | dc |
| C. | both a & b |
| D. | none of the above |
| Answer» C. both a & b | |
| 526. |
In MPT, skin effect comes into picture due to                current |
| A. | ac |
| B. | dc |
| C. | both a & b |
| D. | none of the above |
| Answer» B. dc | |
| 527. |
To find out the transverse crack, Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â magnetic field has to apply, in MPT |
| A. | lengthwise |
| B. | circular |
| C. | parallel to crack |
| D. | none of the above |
| Answer» C. parallel to crack | |
| 528. |
ferromagnetic powder suspended on surface with carrier such as |
| A. | water |
| B. | alcohol |
| C. | keroscene |
| D. | none of the above |
| Answer» D. none of the above | |
| 529. |
In MPT, when the part is magnetised                       , transverse cracks are easily detected |
| A. | lengthwise |
| B. | circular |
| C. | parallel to crack |
| D. | none of the above |
| Answer» B. circular | |
| 530. |
Select odd options :- Couplant is used in Ultrasonic Testing to |
| A. | remove air gap |
| B. | clean the surface |
| C. | for better contact |
| D. | for lubrication purpose |
| Answer» C. for better contact | |
| 531. |
select odd options :- Magnetic partical test is not suitable for |
| A. | gray cast iron |
| B. | chilled cast iron |
| C. | aluminium |
| D. | steel |
| Answer» D. steel | |
| 532. |
Internal Discontinuities in the shaft for elctric motor can be checked by |
| A. | ultrasonic testing |
| B. | dye penetrant test |
| C. | magnetic particle test |
| D. | eddy current test |
| Answer» B. dye penetrant test | |
| 533. |
Time of travel of waves from the defect is…… for Pulse Echo method |
| A. | more |
| B. | less |
| C. | 1/4 of the total time |
| D. | 1/3 of the toal time |
| Answer» C. 1/4 of the total time | |
| 534. |
Which of the following method uses two transducers? |
| A. | pulse echo |
| B. | through transmission |
| C. | eddy current test |
| D. | magnetic particle test |
| Answer» C. eddy current test | |
| 535. |
Which of the following method is used for finding the internal defects of material? |
| A. | ultrasonic testing |
| B. | dye penetrant test |
| C. | magnetic particle test |
| D. | eddy current test |
| Answer» B. dye penetrant test | |
| 536. |
Which factor of ultrasonic waves is measured in Ultrasonic Testing? |
| A. | wavelength |
| B. | speed of waves |
| C. | time of travel |
| D. | distance traveled |
| Answer» D. distance traveled | |
| 537. |
Which of the following method uses the principle of SONAR |
| A. | eddy current test |
| B. | ultrasonic testing |
| C. | x- ray detection |
| D. | ?- ray detection |
| Answer» C. x- ray detection | |
| 538. |
Advantages of Non destructive Testings are |
| A. | no surface damage |
| B. | part canbe reused |
| C. | fast method |
| D. | all of the above |
| Answer» E. | |
| 539. |
Which of the following tests is a NDT |
| A. | tensile test |
| B. | creep test |
| C. | bend test |
| D. | visual inspection |
| Answer» E. | |
| 540. |
Which of the following is not NDT |
| A. | magnetic particle testing |
| B. | dye penetrant test |
| C. | visual inspection |
| D. | vicker\s hardness test |
| Answer» E. | |
| 541. |
Specimen can be reused after the NDT |
| A. | immediately |
| B. | never |
| C. | after some treatment |
| D. | can\t say |
| Answer» E. | |
| 542. |
For Visual Inspection |
| A. | lower magnificati o n is used |
| B. | higher magnification is used |
| C. | microscope is used |
| D. | non of the above |
| Answer» B. higher magnification is used | |
| 543. |
Cleaning of surface is important in DPT |
| A. | required |
| B. | partially required |
| C. | not required |
| D. | none of the above |
| Answer» B. partially required | |
| 544. |
DPT is suitable for |
| A. | rolled products |
| B. | cast products |
| C. | powder metallurgy products |
| D. | heterogeneo us components |
| Answer» B. cast products | |
| 545. |
DPT cannot be used for |
| A. | plastics |
| B. | metals |
| C. | ceramics |
| D. | can be used for all |
| Answer» E. | |
| 546. |
Liquid Penetrant Test is based on the Principle of |
| A. | gravity |
| B. | capillarity |
| C. | partial pressure |
| D. | expansion |
| Answer» C. partial pressure | |
| 547. |
Developer is poured........ The penetrant |
| A. | before |
| B. | after |
| C. | at the same time |
| D. | at the start |
| Answer» C. at the same time | |
| 548. |
Penetrant comes out of the cracks by |
| A. | surface tension |
| B. | gravity |
| C. | capillarity |
| D. | by external pressure |
| Answer» B. gravity | |
| 549. |
Dye Penetrant penetrates inside the crack by |
| A. | surface tension |
| B. | gravity |
| C. | capillarity |
| D. | by external pressure |
| Answer» D. by external pressure | |
| 550. |
Internal Defects can be detected by Dye Penetrant Test |
| A. | always |
| B. | never |
| C. | fine internal cracks |
| D. | broad cracks only |
| Answer» C. fine internal cracks | |