MCQOPTIONS
Saved Bookmarks
MCQOPTIONS
This section includes 29 Mcqs, each offering curated multiple-choice questions to sharpen your Engineering Metrology knowledge and support exam preparation. Choose a topic below to get started.
| 1. |
Which of the following is used to detect the modulated reflected light from any irregularity on the surface? |
| A. | Television camera |
| B. | Light intensity sensor |
| C. | Modulator |
| D. | Video processor |
| Answer» E. | |
| 2. |
Which of the following is mounted on a robot arm for inspecting complicated surfaces? |
| A. | Vision sensor |
| B. | Proximity sensor |
| C. | Heat sensor |
| D. | Touch sensor |
| Answer» B. Proximity sensor | |
| 3. |
In order to have an interference fit, it is essential that the lower limit of the shaft should be: |
| A. | Greater than upper limit of the hole |
| B. | Lesser than upper limit of the hole |
| C. | Greater than lower limit of the hole |
| D. | Lesser than lower limit of the hole |
| Answer» B. Lesser than upper limit of the hole | |
| 4. |
By which of the following procedures, the slip gauges are joined together? |
| A. | Reaming |
| B. | Wringing |
| C. | Heat treatment |
| D. | Packing |
| Answer» C. Heat treatment | |
| 5. |
One micron is equal to ______ Centimetre. |
| A. | 1/1000 |
| B. | 1/100 |
| C. | 1/10 |
| D. | 1/10000 |
| Answer» E. | |
| 6. |
Bore gauge is used for measuring the _______. |
| A. | depth of a hole |
| B. | diameter with an accuracy of 0.05 mm |
| C. | outside diameter of a shaft |
| D. | inside diameter of a hole |
| Answer» E. | |
| 7. |
For which surfaces, is a spirit level used for testing straightness ? |
| A. | Horizontal surfaces |
| B. | Both Horizontal and vertical surfaces |
| C. | Inclined surfaces |
| D. | Vertical surfaces |
| Answer» B. Both Horizontal and vertical surfaces | |
| 8. |
A Metric Outside micrometer of range 100-125 mm is used to measure the diameter of a rod. Barrel graduation showed 16.5 and the thimble graduation in line with the barrel datum line was 28. What is the diameter of the rod? |
| A. | 16.78 mm |
| B. | 16.64 mm |
| C. | 1664 mm |
| D. | 116.78 mm |
| Answer» E. | |
| 9. |
‘GO’ and ‘NO GO’ gauge is a type of |
| A. | Limit gauge |
| B. | Ring gauge |
| C. | Slip gauge |
| D. | Plug gauge |
| Answer» B. Ring gauge | |
| 10. |
A fit designated as 30H7/g6 is a |
| A. | Clearance fit |
| B. | Transition fit |
| C. | Interference fit |
| D. | Tolerance fit |
| Answer» B. Transition fit | |
| 11. |
In a hole basis system, the lower deviation for the hole ‘H’ is |
| A. | 0 mm |
| B. | 0.1 mm |
| C. | 1 mm |
| D. | 0.01 mm |
| Answer» B. 0.1 mm | |
| 12. |
A feeler gauge is used for |
| A. | Checking accuracy of holes |
| B. | Checking gap between the mating parts |
| C. | Checking radii of jobs |
| D. | Adjusting the parts for play |
| Answer» C. Checking radii of jobs | |
| 13. |
For a hole designated as 28 ± 0.5 mm, the tolerance is |
| A. | 0.5 mm |
| B. | 1 mm |
| C. | 28 mm |
| D. | 28.5 mm |
| Answer» C. 28 mm | |
| 14. |
_______ is an example of transition fit. |
| A. | Running fit |
| B. | Expansion fit |
| C. | Wringing fit |
| D. | Shrinkage fit |
| Answer» D. Shrinkage fit | |
| 15. |
In the hole basis system, the hole is kept constant & the size of the _____ is varied to get the desired fit. |
| A. | Tolerance |
| B. | Shaft |
| C. | Hole |
| D. | Fit |
| Answer» C. Hole | |
| 16. |
Hardness of slip gauges should be, |
| A. | 55 HRC |
| B. | 58 HRC |
| C. | 64 HRC |
| D. | 50 HRC |
| Answer» D. 50 HRC | |
| 17. |
If the hole size is 25+0.000/+0.021 & the shaft size is 25+0.022/+0.035 the minimum interference is |
| A. | 0.035 mm |
| B. | 0.001 mm |
| C. | 0.021 mm |
| D. | 0.022 mm |
| Answer» C. 0.021 mm | |
| 18. |
In mass production, parts made to definite limit of error is called as ______ |
| A. | Selective assembly |
| B. | Tolerance |
| C. | Allowance |
| D. | Interchangeability |
| Answer» E. | |
| 19. |
In an assembly, Hole size is smaller than shaft size then this type of fit is known as ______ |
| A. | Clearance fit |
| B. | Interference fit |
| C. | Transition fit |
| D. | Sliding fit |
| Answer» C. Transition fit | |
| 20. |
WHICH_OF_THE_FOLLOWING_IS_MOUNTED_ON_A_ROBOT_ARM_FOR_INSPECTING_COMPLICATED_SURFACES??$ |
| A. | Vision sensor |
| B. | Proximity sensor |
| C. | Heat sensor |
| D. | Touch sensor |
| Answer» B. Proximity sensor | |
| 21. |
Which_of_the_following_is_used_to_detect_the_modulated_reflected_light_from_any_irregularity_on_the_surface?$ |
| A. | Television camera |
| B. | Light intensity sensor |
| C. | Modulator |
| D. | Video processor |
| Answer» E. | |
| 22. |
What is another name of computer aided inspection? |
| A. | Computer aided machining |
| B. | Visionary machining |
| C. | Machine vision |
| D. | Visionary inspection |
| Answer» D. Visionary inspection | |
| 23. |
How many points are needed on the circumference to define a circle by computer? |
| A. | One |
| B. | Two |
| C. | Three |
| D. | Four |
| Answer» D. Four | |
| 24. |
Which of the following is used for automatic inspection? |
| A. | Universal probes |
| B. | Hydrolysis probes |
| C. | Electronic probes |
| D. | Mechanical probes |
| Answer» B. Hydrolysis probes | |
| 25. |
What is the use of stroboscope technology? |
| A. | Optically freezing the motion of rotating part |
| B. | Mechanically freezing the motion of reciprocating part |
| C. | Optically freezing the motion of reciprocating and rotating part |
| D. | Mechanically freezing the motion of reciprocating and rotating part |
| Answer» D. Mechanically freezing the motion of reciprocating and rotating part | |
| 26. |
How many levels are organized in an inspection data handling? |
| A. | 1 |
| B. | 2 |
| C. | 3 |
| D. | 4 |
| Answer» C. 3 | |
| 27. |
Which of the following is used to control the robot arm? |
| A. | Microprocessor |
| B. | Keyboard |
| C. | Mouse |
| D. | Computer |
| Answer» B. Keyboard | |
| 28. |
How many degrees of freedom is in the robotic arm? |
| A. | 1 |
| B. | 2 |
| C. | 3 |
| D. | 4 |
| Answer» E. | |
| 29. |
How a system is used to check the surface finish of a surface by CAI? |
| A. | As a mirror |
| B. | As a lens |
| C. | As a black body |
| D. | As a grey body |
| Answer» B. As a lens | |