*/*_The frictional torque transmitted in a truncated conical pivot bearing, considering uniform wear, is?

(2/3).≈í¬∫ W cosec ≈í¬± (r‚Äö√á√Ö + r‚Äö√á√á)

(1/2). ≈í¬∫ W cosec ≈í¬± (r‚Äö√á√Ö + r‚Äö√á√á)

(1/2). ≈í¬∫ W cosec ≈í¬± [(r‚Äö√á√Ö¬¨‚â• - r‚Äö√á√á¬¨‚â•)/(r‚Äö√á√Ö¬¨‚â§ - r‚Äö√á√á¬¨‚â§)]

(2/3). ≈í¬∫ W cosec ≈í¬± [(r‚Äö√á√Ö¬¨‚â• - r‚Äö√á√á¬¨‚â•)/(r‚Äö√á√Ö¬¨‚â§ - r‚Äö√á√á¬¨‚â§)]

*/*_The frictional torque transmitted in a truncated conical pivot bea

1.	/_The frictional torque transmitted in a truncated conical pivot bearing, considering uniform wear, is?
A.	(1/2). ≈í¬∫ W cosec ≈í¬± (r‚Äö√á√Ö + r‚Äö√á√á)
B.	(2/3).≈í¬∫ W cosec ≈í¬± (r‚Äö√á√Ö + r‚Äö√á√á)
C.	(1/2). ≈í¬∫ W cosec ≈í¬± [(r‚Äö√á√Ö¬¨‚â• - r‚Äö√á√á¬¨‚â•)/(r‚Äö√á√Ö¬¨‚â§ - r‚Äö√á√á¬¨‚â§)]
D.	(2/3). ≈í¬∫ W cosec ≈í¬± [(r‚Äö√á√Ö¬¨‚â• - r‚Äö√á√á¬¨‚â•)/(r‚Äö√á√Ö¬¨‚â§ - r‚Äö√á√á¬¨‚â§)]
Answer» B. (2/3).≈í¬∫ W cosec ≈í¬± (r‚Äö√á√Ö + r‚Äö√á√á)

Discussion

No Comment Found

Related MCQs

In a four-bar chain it is required to give an oscillatory motion to the follower for a continuous rotation of the crank. For the lengths of 50 mm of crank and 70 mm of the follower, determine theoretical maximum length of coupler. The distance between fixed pivots of crank and followers is
The relation l = (2/3).(j + 2) apply only to kinematic chains in which lower pairs are used. This may be used to kinematic chains in which higher pairs are used, but each higher pair may be taken as equivalent to
A rotor which is balanced statically but not dynamically is supported on two bearings L apart and at high speed of the rotor, reaction on the left bearing is R. The right side of the bearing is shifted to a new position 2L apart from the left bearing. At the same rotor speed, dynamic reaction on the left bearing in the new arrangement will
A friction circle is a circle drawn when a journal rotates in a bearing. Its radius depends upon the coefficient of friction and the
The frictional torque transmitted in a flat pivot bearing, assuming uniform wear, is (Where μ = Coefficient of friction, W=Load over the bearing, R=Radius of bearing)
The velocity of sliding of meshing gear teeth is (Where ω₁ and ω₂ are angular velocities of meshing gears and ‘y’ is distance between point of contact and the pitch point)
A typewriter mechanism has 7 numbers of binary joints, six links and none of higher pairs. The mechanism is
In a steam engine, the earlier cut-off with a simple slide valve may be obtained by increasing the steam lap and the angle of advance of the eccentric but keeping constant the travel and lead of the valve, this method will
In a steam engine, one method of obtaining the earlier cut-off with a simple slide valve is by increasing the angle of advance of the eccentric while the throw of the eccentric, steam lap and exhaust lap are kept constant. This method will
ABCD is a four bar mechanism in which AB = 310 mm and CD = 450 mm. AB and CD are both perpendicular to the fixed link AD, as shown in the below figure. If the velocity of B at this condition is v. Then the velocity of C is

*/*_The frictional torque transmitted in a truncated conical pivot bearing, considering uniform wear, is?

Discussion

No Comment Found

Related MCQs

Reply to Comment

/_The frictional torque transmitted in a truncated conical pivot bearing, considering uniform wear, is?